Partial Denture I Test

Method to determine height of floor of the mouth is:

The junction of mandibular minor connector with major connector is :

An ideal clasp assembly should possess the following quality:

Fulcrum line ជាបន្ទាត់មួយរត់កាត់តាមៈ:

Approach arm រត់តាមបណ្តោយសាច់ mucosa ហើយ តភ្ជាប់ជាមួយៈ:

ទំពក់ Circlet:

Setting of a RPD may occur due to one of the following reasons, except:

When designing palatal major connectors ,relief should for:

The correct answer the basic movements of the mandible:

The basic philosophy of dental treatment for a partially edentulous patient:

The superior border of mandibular lingual bar major connector should be:

The Gridwork of Minor Connector on a maxillary class 1 RPD:

Ring Clasp:

3 weeks after insertion of distal extension partial denture, the patient reports to the dental clinic with complaint of sensitivity to chewing pressure. The most probable reason would be :

Tripod of dental surveyor is the method used:

Bar Clasp គេប្រើទៅលើ :

Major Connector ជាស្ពានៈ:

Bar Clasp ជាប្រភេទទំពក់:

Reciprocal clasp arm of RPD should be:

Function of the teeth is /are:

Lattice type of grid work minor connectors is:

Tissue stops are useful in:

The major connector in this mandibular class I removable partial denture:

សមាសភាពនៃធ្មេញដាក់ដោះមួយផ្នែក :

Ina cast partial denture wearer, the stresses transferred to the abutment teeth are decreased if :

Intracoronal retainer mechanism is:

Important factor in determining the path of insertion/dislodgement is:

Physiologic Rest in a position of vertical dimension which can be recorded with:

A clasp most common use is?:

សាច់ដុំ Elevation or closure of the mouth:

Function of denture bases :

Multiple clasps are joined at :

The total retention for a RPD is obtained from:

For the preparation of rest seat:

ទិសដៅធ្មេញដោះដាក់មួយផ្នែកអោយប្រសើរនូវៈ:

ចំណាត់ថ្នាក់ទី 3 នៃចន្លោះធ្មេញ គឺប្រឡោះធ្មេញៈ:

Following are the intended functions of guiding planes, except:

សារៈប្រយោជន៍នៃធ្មេញដាក់ដោះមួយផ្នែកដើម្បីៈ:

In a class III modification 1 RPD, the rests are usually placed:

Marginal ridge for a rest seat should be reduced by at least:

In an infrabulge clasp, the clasp arm arises either from:

The support for a RPD is usually :

Bar Clasp វាគ្របលើក្រឡាផ្ទៃ :

Methods to check loss of support for distal extension denture base include following except:

Guiding planes which are not in the same parallel plane horizontally:

លក្ខខ័ណ្ឌដែលត្រូវធ្វើធ្មេញដាក់ដោះមួយផ្នែកត្រូវប្រើៈ:

សារៈប្រយោជន៍នៃធ្មេញដាក់ដោះមួយផ្នែកដើម្បីៈ:

Major Connector ផ្តល់នូវការទ្រទ្រង់បែបៈ:

The only one flexible minor connectors is :

Which type of RPD can best resist the forces, to which it is subjected? :

Approach arm វាចូលដល់ Undercut តាមរយៈ :

The major connector in this mandibular class I removable partial denture:

Mandibular gridwork design of minor connectors:

Minor Connector តភ្ជាប់ទៅៈ:

Incisal rests:

Reciprocal Arm សន្តូក :

Maxillary major connectors most common use is:

The total retention for a RPD is obtained from:

A minor connector located at embrasure should be:

The relation of the cast to surveyor can be recorded in the following manner: